WordPress database error: [Duplicate entry '9734' for key 1]
INSERT INTO wp_bas_visitors (visit_ip, referer, osystem, useragent, lasthere) VALUES (644300604, 2, 210, 1321, '2009-01-07 01:38:16');

WordPress database error: [You have an error in your SQL syntax; check the manual that corresponds to your MySQL server version for the right syntax to use near 'AND referer = referer_id AND osystem = os_id AND useragent = ua_]
SELECT * FROM wp_bas_visitors, wp_bas_refer, wp_bas_ua, wp_bas_os WHERE visit_id = AND referer = referer_id AND osystem = os_id AND useragent = ua_id

WordPress database error: [You have an error in your SQL syntax; check the manual that corresponds to your MySQL server version for the right syntax to use near ' '2009-01-07 01:38:16', 0, 98)' at line 1]
INSERT INTO wp_bas_log (visit, stamp, outbound, page) VALUES (, '2009-01-07 01:38:16', 0, 98);

Prepare Your House For Sale » How To Replace A Door Knob

How To Replace A Door Knob

September 22, 2007 on 2:23 pm | In How To / Repair Your House |

The door knob is a very needed item in your home.  Think about it, if you did not have any?  Ok, a little humor here today.  The style is up to you.  What do you need the new door knob for?  All new remodel or just a broken handle in your house.  The style should stay the same through out the house.  It gives the look of good clean lines with all matching,  non-matching can be viewed poorly by many people.

The door knob is a standard size for the most part.  If you get into a designer knob make sure you have the correct size opening to put it in.  If you don’t you will need what is called a hole cutting saw.  Now that you have your door knob lets take the old one out. 

The following tools will be helpful.

-standard screw driver

-Philips head screw driver

-wood chisels

-hammer

The above tools may not all be needed.  There are normally two screws on each side of the handle on the inside of the door. remove these screws.  Once screws are out of the handle, it should just pull apart from each side. The striker or plunger is held in the center of the door by two screws one on the top and bottom.  These are seated well most times and need some  work to get them out.  There should  be nothing left in the holes.  Slide your new  striker or plunger in and then take the handle and slide it in from each side.  Make sure if it is locking type that the lock switch is on the inside of the room side of the door.  Tighten up the screws on the plunger now.  You can then tighten the screws on the door handle now also.

That should complete your installation of the door knob.  The only way this would not be done is if you needed to chisel the around the striker / plunger to make the new one fit.  This is normally not needed.  Which you would have seen this when you attempted to slide it in.

The tools above can be narrowed down to one cordless screw driver and a standard/Philips head bit can do the whole door knob installation.

So, there you have it.  Now step back and look at your new door knob.

Remember safety first.

Sphere: Related Content

No Comments yet »

RSS feed for comments on this post. TrackBack URI

Leave a comment

XHTML: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <code> <em> <i> <strike> <strong>

Blogroll

  • Badges Properties LLC - A site which helps people with their remodeling, repairing and new lawn hydroseeding needs.
  • Fix Your House - How to fix or repair your house and more.
  • Houses To Go - A site about helping people help their homes
  • Kitchen Design - Everything you need to know about Interior Design. Redecorating your home made easy.
get a free page counter with chart at www.blogskinny.com

Helping bloggers find readers with free tools.
Shop at Compare4.us Every Item For Your House And Garden

Meta:

Powered by WordPress with Pool theme design by Borja Fernandez.
Entries and comments feeds. Valid XHTML and CSS. ^Top^